接外包,有相关需求的可以联系我:Telegram | Email

如何配置ESP32-C3的SSD1306模块?

该文章创建(更新)于02/4/2023,请注意文章的时效性!

之前配置SSD1306发现缺少相关模块,是需要手动去配置一下的,简单说就是新建一个文件配置相关SSD1306的显示类即可。

  • SSD1306.py

显示核心就是下面这个SSD1306类

# MicroPython SSD1306 OLED driver, I2C and SPI interfaces

from micropython import const
import framebuf


# register definitions
SET_CONTRAST = const(0x81)
SET_ENTIRE_ON = const(0xA4)
SET_NORM_INV = const(0xA6)
SET_DISP = const(0xAE)
SET_MEM_ADDR = const(0x20)
SET_COL_ADDR = const(0x21)
SET_PAGE_ADDR = const(0x22)
SET_DISP_START_LINE = const(0x40)
SET_SEG_REMAP = const(0xA0)
SET_MUX_RATIO = const(0xA8)
SET_COM_OUT_DIR = const(0xC0)
SET_DISP_OFFSET = const(0xD3)
SET_COM_PIN_CFG = const(0xDA)
SET_DISP_CLK_DIV = const(0xD5)
SET_PRECHARGE = const(0xD9)
SET_VCOM_DESEL = const(0xDB)
SET_CHARGE_PUMP = const(0x8D)

# Subclassing FrameBuffer provides support for graphics primitives
# http://docs.micropython.org/en/latest/pyboard/library/framebuf.html
class SSD1306(framebuf.FrameBuffer):
    def __init__(self, width, height, external_vcc):
        self.width = width
        self.height = height
        self.external_vcc = external_vcc
        self.pages = self.height // 8
        self.buffer = bytearray(self.pages * self.width)
        super().__init__(self.buffer, self.width, self.height, framebuf.MONO_VLSB)
        self.init_display()

    def init_display(self):
        for cmd in (
            SET_DISP | 0x00,  # off
            # address setting
            SET_MEM_ADDR,
            0x00,  # horizontal
            # resolution and layout
            SET_DISP_START_LINE | 0x00,
            SET_SEG_REMAP | 0x01,  # column addr 127 mapped to SEG0
            SET_MUX_RATIO,
            self.height - 1,
            SET_COM_OUT_DIR | 0x08,  # scan from COM[N] to COM0
            SET_DISP_OFFSET,
            0x00,
            SET_COM_PIN_CFG,
            0x02 if self.width > 2 * self.height else 0x12,
            # timing and driving scheme
            SET_DISP_CLK_DIV,
            0x80,
            SET_PRECHARGE,
            0x22 if self.external_vcc else 0xF1,
            SET_VCOM_DESEL,
            0x30,  # 0.83*Vcc
            # display
            SET_CONTRAST,
            0xFF,  # maximum
            SET_ENTIRE_ON,  # output follows RAM contents
            SET_NORM_INV,  # not inverted
            # charge pump
            SET_CHARGE_PUMP,
            0x10 if self.external_vcc else 0x14,
            SET_DISP | 0x01,
        ):  # on
            self.write_cmd(cmd)
        self.fill(0)
        self.show()

    def poweroff(self):
        self.write_cmd(SET_DISP | 0x00)

    def poweron(self):
        self.write_cmd(SET_DISP | 0x01)

    def contrast(self, contrast):
        self.write_cmd(SET_CONTRAST)
        self.write_cmd(contrast)

    def invert(self, invert):
        self.write_cmd(SET_NORM_INV | (invert & 1))

    def show(self):
        x0 = 0
        x1 = self.width - 1
        if self.width == 64:
            # displays with width of 64 pixels are shifted by 32
            x0 += 32
            x1 += 32
        self.write_cmd(SET_COL_ADDR)
        self.write_cmd(x0)
        self.write_cmd(x1)
        self.write_cmd(SET_PAGE_ADDR)
        self.write_cmd(0)
        self.write_cmd(self.pages - 1)
        self.write_data(self.buffer)


class SSD1306_I2C(SSD1306):
    def __init__(self, width, height, i2c, addr=0x3C, external_vcc=False):
        self.i2c = i2c
        self.addr = addr
        self.temp = bytearray(2)
        self.write_list = [b"\x40", None]  # Co=0, D/C#=1
        super().__init__(width, height, external_vcc)

    def write_cmd(self, cmd):
        self.temp[0] = 0x80  # Co=1, D/C#=0
        self.temp[1] = cmd
        self.i2c.writeto(self.addr, self.temp)

    def write_data(self, buf):
        self.write_list[1] = buf
        self.i2c.writevto(self.addr, self.write_list)


class SSD1306_SPI(SSD1306):
    def __init__(self, width, height, spi, dc, res, cs, external_vcc=False):
        self.rate = 10 * 1024 * 1024
        dc.init(dc.OUT, value=0)
        res.init(res.OUT, value=0)
        cs.init(cs.OUT, value=1)
        self.spi = spi
        self.dc = dc
        self.res = res
        self.cs = cs
        import time

        self.res(1)
        time.sleep_ms(1)
        self.res(0)
        time.sleep_ms(10)
        self.res(1)
        super().__init__(width, height, external_vcc)

    def write_cmd(self, cmd):
        self.spi.init(baudrate=self.rate, polarity=0, phase=0)
        self.cs(1)
        self.dc(0)
        self.cs(0)
        self.spi.write(bytearray([cmd]))
        self.cs(1)

    def write_data(self, buf):
        self.spi.init(baudrate=self.rate, polarity=0, phase=0)
        self.cs(1)
        self.dc(1)
        self.cs(0)
        self.spi.write(buf)
        self.cs(1)
  • boot.py

测试用例

from machine import I2C,Pin #从 machine 模块导入 I2C、 Pin 子模块
from SSD1306 import SSD1306_I2C #从 ssd1306 模块中导入 SSD1306_I2C 子模块
import time

i2c = I2C(sda=Pin(10), scl=Pin(9)) #I2C 初始化: sda-->13, scl -->14
#OLED 显示屏初始化: 128*64 分辨率,OLED 的 I2C 地址是 0x3c

oled = SSD1306_I2C(128, 64, i2c, addr=0x3c)
while True:
    oled.fill(0) ###清空当前屏幕,当1时,填充满屏幕
    oled.show()  ###显示
    time.sleep(1)  ###等待1秒

    oled.rect(0, 0, 128, 64, 1)
    oled.show()
    time.sleep(1)

    oled.rect(32, 16, 64, 32, 1)
    oled.show()
    time.sleep(1)

    oled.fill(0)  # 清空内容后再单独绘制字符
    oled.text("MicroPython test", 0, 20)  #在指定位置显示英文字符
    oled.show()
    time.sleep(1)

要不赞赏一下?

微信
支付宝
PayPal
Bitcoin

版权声明 | Copyright

除非特别说明,本博客所有作品均采用知识共享署名-非商业性使用-禁止演绎 4.0 国际许可协议进行许可。转载请注明转自-
https://www.emperinter.info/2023/02/04/how-to-configure-the-ssd1306-module-of-esp32-c3/


要不聊聊?

我相信你准备留下的内容是经过思考的!【勾选防爬虫,未勾选无法留言】

*

*



YouTube | B站

微信公众号

👉 NewsLetter ❤️ 邮箱订阅 👈

优惠码

阿里云国际版20美元
Vultr10美元
搬瓦工 | Bandwagon应该有折扣吧?
Just My SocksJMS9272283 【注意手动复制去跳转】
域名 | namesiloemperinter(1美元)
币安 币安